Mandriva 2010 : Telkomsel Flash With Wvdial

Dial up using GSM Provider (Telkomsel) with Nokia 5320

Set Nokia 5320 to PC Suite
setting > phone setting > connection > usb > pc suite

Install wvdial

urpmi wvdial

Configuring wvdial

wvdialconf

[root@srempuan box]# wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyACM0<*1>: ATQ0 V1 E1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 Z -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyACM0<*1>: Modem Identifier: ATI -- Nokia
ttyACM0<*1>: Speed 4800: AT -- OK
ttyACM0<*1>: Speed 9600: AT -- OK
ttyACM0<*1>: Speed 19200: AT -- OK
ttyACM0<*1>: Speed 38400: AT -- OK
ttyACM0<*1>: Speed 57600: AT -- OK
ttyACM0<*1>: Speed 115200: AT -- OK
ttyACM0<*1>: Speed 230400: AT -- OK
ttyACM0<*1>: Speed 460800: AT -- OK
ttyACM0<*1>: Max speed is 460800; that should be safe.
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

Found an USB modem on /dev/ttyACM0.
/etc/wvdial.conf: Can't open '/etc/wvdial.conf' for reading: No such file or directory
/etc/wvdial.conf: ...starting with blank configuration.
Modem configuration written to /etc/wvdial.conf.
ttyACM0: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
[root@srempuan box]#

and check the configuration file in /etc/wvdial.conf

[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = USB Modem
; Phone =
ISDN = 0
; Username =
Init1 = ATZ
; Password =
Modem = /dev/ttyACM0
Baud = 460800
/etc/wvdial.conf lines 1-11/11 (END)

for telkomsel flash change to :

[Dialer Defaults]
Modem Type = USB Modem
Modem = /dev/ttyACM0
Baud = 460800
Init2 = AT+CGDCONT=1,"IP","internet"
Phone = *99#
Username = 'telkomsel'
Password = 'telkomsel'
Ask Password = 0
Dial Command = ATDT
Stupid Mode = 1
Idle Seconds = 3000
ISDN = 0
Auto DNS = 1

Lets run it

[box@srempuan ~]$ wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: AT+CGDCONT=1,"IP","internet"
AT+CGDCONT=1,"IP","internet"
OK
--> Modem initialized.
--> Idle Seconds = 3000, disabling automatic reconnect.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99#
CONNECT
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Tue Jan 12 08:05:35 2010
--> Pid of pppd: 27238
--> Using interface ppp0
--> pppd: Connect: ppp0 <--> /dev/ttyACM0
--> pppd: PAP authentication succeeded
--> pppd: not replacing existing default route via 192.168.1.1
--> local IP address 114.120.155.152
--> remote IP address 10.6.6.6
--> primary DNS address 114.127.208.84
--> secondary DNS address 202.3.208.11


To Disconnect, hit Ctrl+C